Specifications Standards & Data: Difference between revisions
(Created page with "{{DRM_page_menu}} 674x674px|frameless|right|alt=Engineering Help| Engineering __TOC__ A complete listing of various Government and approved Non-Government documents used in the preparation of engineering drawings. Documents listed herein are applicable only as specified in the contract or DRAWING REQUIREMENTS MANUAL (DRM) sections. ==Specifications & Standards Data== ===Scope=== ====Purpose==== This section lists various Government and appr...") |
No edit summary |
||
| Line 19: | Line 19: | ||
'''Note:''' DoD Policy Memo 05-3 “Elimination of Waivers to Cite Military Specifications and Standards in Solicitation and Contracts” has eliminated the need for waivers to use MIL-SPECS and MIL-STDS on DoD contracts. (See PREFACE 1, Section 2) | '''Note:''' DoD Policy Memo 05-3 “Elimination of Waivers to Cite Military Specifications and Standards in Solicitation and Contracts” has eliminated the need for waivers to use MIL-SPECS and MIL-STDS on DoD contracts. (See PREFACE 1, Section 2) | ||
====Currency of Documents==== | |||
The documents listed below accompanied by their date were current and in effect as of March 2008, the cutoff date for the publication of this Eleventh (11th) edition of the DRM. | |||
NOTE: Document's source is listed for each grouping. All documents are available through a single source from IHS. See page ii for source information. | |||
===COMPANY STANDARDS, SPECIFICATIONS, AND PROCEDURES=== | |||
====Company Standard Requirements==== | |||
Company Standards shall meet the following requirements. | |||
* Is identified by name and address of issuing company, CAGE number, document nomenclature and number, and contract number. | |||
* Does not contain limited rights in technical data. | |||
* Provide the necessary design disclosure information for the level of drawing for which they are furnished. | |||
* Satisfy the same procurement requirements as for a specification control drawing when it defines a vendor item. | |||
* Drawing practices and symbols used are such that their intent and interpretation are clear and unambiguous whether of standard or non-standard origin. | |||
* Have clarity, legibility and reproducibility of MIL-PRF-5480 for the purpose of microfilming. | |||
* All documents referenced in a company standard shall also be supplied when not covered by a military, government, or non-government standard or specification. | |||
[[Category:Engineering]] | [[Category:Engineering]] | ||
[[Category:Drawing Requirements Manual]] | [[Category:Drawing Requirements Manual]] | ||
Revision as of 16:37, 18 December 2024
A complete listing of various Government and approved Non-Government documents used in the preparation of engineering drawings.
Documents listed herein are applicable only as specified in the contract or DRAWING REQUIREMENTS MANUAL (DRM) sections.
Specifications & Standards Data
Scope
Purpose
This section lists various Government and approved Non-Government documents used in the preparation of engineering drawings. Documents listed herein are applicable only as specified in the contract or DRAWING REQUIREMENTS MANUAL (DRM) sections.
Applicable Documents
Note: DoD Policy Memo 05-3 “Elimination of Waivers to Cite Military Specifications and Standards in Solicitation and Contracts” has eliminated the need for waivers to use MIL-SPECS and MIL-STDS on DoD contracts. (See PREFACE 1, Section 2)
Currency of Documents
The documents listed below accompanied by their date were current and in effect as of March 2008, the cutoff date for the publication of this Eleventh (11th) edition of the DRM.
NOTE: Document's source is listed for each grouping. All documents are available through a single source from IHS. See page ii for source information.
COMPANY STANDARDS, SPECIFICATIONS, AND PROCEDURES
Company Standard Requirements
Company Standards shall meet the following requirements.
- Is identified by name and address of issuing company, CAGE number, document nomenclature and number, and contract number.
- Does not contain limited rights in technical data.
- Provide the necessary design disclosure information for the level of drawing for which they are furnished.
- Satisfy the same procurement requirements as for a specification control drawing when it defines a vendor item.
- Drawing practices and symbols used are such that their intent and interpretation are clear and unambiguous whether of standard or non-standard origin.
- Have clarity, legibility and reproducibility of MIL-PRF-5480 for the purpose of microfilming.
- All documents referenced in a company standard shall also be supplied when not covered by a military, government, or non-government standard or specification.